Work we have done
Red de chapa, fibra en falso techo, helicoidal visto y extracción de cocina.
Cooling throughout the whole property with no units on the walls. We make the ductwork to measure and install it ourselves.
Years in the trade
Fitters on the team
Hours to your quote
% Mallorca
We fabricate the ductwork in our own workshop and install it ourselves, island-wide.
Cooling throughout the property with no units on show. We make the ductwork to measure and install it.
The usual duct for interior residential work. Factory insulated, light, and it absorbs air noise.
Tougher, for outdoors, roofs and exposed runs. Insulated with a wrap and foil so it does not condense.
Round steel duct, for exposed runs in warehouses and commercial units or where a lot of air has to move.
For kitchen extraction and seafront properties. AISI 304 and 316, made to measure in our own workshop.
Canopies, stainless ductwork, make-up air and roof discharge. For restaurants, bars and hotels.
Extract and supply air for warehouses, car parks, shops and offices. Sized for how the space is actually used.
Cortamos y plegamos en nuestro taller antes de pisar la obra. Y servimos a instaladoras a precio de industrial.
Para comunidades y administradores de fincas. Si tiene un requerimiento, se lo miramos antes de presupuestar.
Red de chapa, fibra en falso techo, helicoidal visto y extracción de cocina.
With a ducted system there is one single unit hidden above the ceiling, and the air is distributed through ductwork to grilles in the ceiling of each room. From inside the property you see no equipment at all, only the grilles.
No units on the walls, in the lounge or the bedrooms. In a well finished home or a holiday rental villa, that matters.
One outdoor unit instead of three or four. Less noise outside and far less impact on the facade, which in central Palma and in protected areas can be the difference between being allowed to install or not.
More even distribution. Air enters at several points rather than blasting from one wall, so you do not end up with a freezing bedroom and a hallway at thirty degrees.
Zoning is possible. With motorised grilles and a thermostat per zone, each part of the property runs at its own temperature and you stop cooling rooms nobody is using.
In return you need space above the ceiling, and the installation is building work rather than an appliance hung on a wall in a morning.
This is the first question to settle and the one that decides whether the project works as drawn or has to be rethought.
The unit needs its space, and the ducts have to run above the ceiling with their insulation. If the clearance is not there, you have three ways out: drop the ceiling only in the hallway and the bathrooms, which is where it shows least, and leave the main rooms at full height; use a shallower, wider duct profile; or switch to cassette or split units in the areas where nothing can pass.
We measure that at the survey. A drawing will not tell you the real clearance left under the beams, and that is where projects go wrong.
Fibreglass (Climaver type). The usual duct for interior residential work. It comes ready insulated thermally and acoustically, it is light, quick to work with and it absorbs air noise, so the installation runs quieter.
Galvanised steel. Tougher, copes far better with damp and with time, and it is what has to go outside, on the roof or anywhere the duct might take a knock. It needs insulating separately, with a wrap and foil, so it does not condense with cold air inside and warm air outside.
Spiral duct. Round steel duct. Used where the ductwork is exposed — warehouses, industrial-style commercial units — or where a lot of air has to move with little resistance.
Stainless steel. For kitchen extraction and aggressive environments. In Mallorca there is another reason: near the coast, salt eats ordinary galvanised steel well before its time, and stainless pays for itself.
Déjanos tus datos y te llamamos para concertar la visita. Medimos y en 48 horas tienes el presupuesto por escrito.
O si lo prefieres, escríbenos por WhatsApp
In short: ducted air conditioning distributes air from a single unit hidden above the ceiling to grilles in each room, with no equipment on show and one outdoor unit. At Conductos Mallorca we fabricate the ductwork to measure in our workshop — fibreglass, galvanised steel, spiral or stainless depending on where it runs — and install it on site with insulation, sealing and access panels. The installation is handed over commissioned and certified by a registered installer. The first thing to check is the real clearance above the ceiling, and that is measured at the survey. We give a fixed written quote within 48 hours and the survey carries no obligation. Phone: 631 651 622.
It depends on the size and on whether it is new build or an occupied property. In a normal home you are usually talking several days, and on new build it is coordinated with the other trades. The timescale is written into the quote.
Yes, but we need to see where the ductwork can run. Normally it goes along the hallway and the bathrooms, dropping the ceiling only there, which is where it is least noticeable. If there is no clearance anywhere, we will tell you and look at another solution rather than sell you something that will look wrong.
It means controlling each area separately with motorised grilles and thermostats. It pays off when different parts of the property are used at different times, or when there are rooms that are hardly used. In a small home in constant use, often it is not needed.
Properly sized, very little. Noise in these systems almost always comes from the same thing: ducts too narrow for the air they have to move, or the wrong grilles. That is solved by sizing it correctly at the start, not afterwards.
The unit has its service, and the ductwork needs to be cleanable. That is why we leave access panels at the points that will need them. Ductwork with no access panels has to be opened by cutting into the ceiling the day it needs cleaning.
Conductos Mallorca fabricates and installs ductwork for air conditioning, ventilation and extraction across the island.
Over 25 years fabricating and installing ductwork in Mallorca: steel, fibreglass, spiral and stainless.
Five fitters on the team. We do not subcontract: the person who quotes the job is the person who fits it.
Ductwork is fabricated before we set foot on site. Fewer days working inside and far less dust.
In writing within 48 hours of the survey, with the metres, the materials and the timescale. What we sign is what you pay.
Conductos Mallorca · Tel. 631 651 622 · Servicio en toda Mallorca (Illes Balears) · Legal notice
Palma, the coastal resort areas and every other municipality on the island.